High Flux RO Membrane for Textile Dyeing Effluent Reuse System
High Flux RO Membrane for Textile Dyeing Effluent Reuse System

High Flux RO Membrane for Textile Dyeing Effluent Reuse System

Introduction:Textile dyeing and finishing plants face continuous pressure to cut freshwater intake and discharge volume, while recovering reusable process water from colored, saline effluent. A high flux RO membrane is the core separation unit inside a dyeing effluent reuse system, working after softening, multimedia filtration, an activated-carbon stage and ultrafiltration to remove residual salts, color, surfactants and dissolved organics. Proper pretreatment stabilizes permeate quality for rinsing, washing and makeup use, lowers chemical consumption, and helps mills meet discharge and recycling targets.

We're here to help:
Easy ways to get the answers you need.

  • Product parameter
  • Inquiry

Product parameter:

Product Introduction

LEFILTER high flux RO membrane elements are spiral-wound thin-film composite elements engineered for industrial wastewater reuse, including dyeing, printing and finishing effluent that has completed pretreatment and ultrafiltration. The product line covers standard 4040 and 8040 formats with compatible center tubes, end caps and seals, so it can be retrofitted into existing pressure vessels without changing the skid layout. On the reuse skid, the RO train is normally protected upstream by a water filter housing holding cartridge or security filters, and a self-cleaning filter handles continuous removal of suspended solids and colloidal load before the membrane inlet.

Compared with a standard brackish-water membrane, this series is optimized for a higher stable permeate flow at comparable operating pressure, with a fouling-resistant sheet structure and spacer design that tolerates moderate organic and colloidal load from textile effluent. It is positioned as an independent compatible replacement element, not an original manufacturer product; referenced brand names are used only to describe fit and performance equivalence.


Working Principle

High Flux RO Membrane for Textile Dyeing Effluent Reuse System

In a dyeing effluent reuse loop, pretreated UF permeate is fed under pressure into the spiral-wound RO element. Water molecules pass through the semi-permeable membrane leaf and travel along the permeate spacer to the central collection tube, forming reusable permeate. Dissolved salts, residual dye molecules, color bodies, surfactants and most remaining organics are rejected and concentrated in the concentrate stream, which is sent to further evaporation, crystallization or discharge treatment.

The feed spacer promotes turbulent cross-flow over the membrane surface to reduce sedimentation of colloidal matter; the permeate spacer carries purified water toward the outlet; end-cap seals prevent bypass and mixing of feed and permeate. Because dyeing effluent carries persistent organic and color load, consistent pretreatment and scheduled CIP remain essential to sustain flux and salt rejection over the element life.


Typical Specifications

ItemSpecification
Element format4040 / 8040 spiral-wound
Membrane typeThin-film composite polyamide
Target feedPretreated + UF-treated textile dyeing effluent, reuse RO feed
Permeate flowHigh-flux rating per format, sized to skid recovery and pressure
Salt rejectionStable rejection of dissolved salts and ionic species under design conditions
Feed temperature range5–45 °C (continuous operation below design upper limit)
Operating pH range4–10
Cleaning pH range2–11 (with appropriate CIP chemicals and rinsing)
Free chlorine tolerance< 0.1 ppm at the membrane inlet; dechlorination upstream required
Seals and hardwareFood-grade / low-leaching seals where specified; standard center tube and end cap
Typical service life2–3 years with protected pretreatment and regular CIP


Core Advantages

High stable flux: 

optimized sheet and spacer design delivers strong permeate output for reuse-oriented flow demands.

Fouling-resistant structure: 

turbulent feed spacer and compatible surface chemistry ease handling of organic and colloidal dyeing load.

Cleanability: 

broad cleaning pH window supports acidic and alkaline CIP to recover flux after organic and color fouling.

Drop-in compatibility: 

standard 4040 / 8040 dimensions and connections suit replacement in existing vessels and skids.

Reuse-oriented economics: 

recovered permeate can substitute freshwater in rinsing and washing stages, reducing intake and effluent cost.


Application Scenarios

High Flux RO Membrane for Textile Dyeing Effluent Reuse System

Dyeing and finishing mill effluent reuse after UF polishing.

Printing and textile wastewater recycling for rinsing, washing and process makeup.

Combined zero-liquid-discharge (ZLD) front-end RO stage ahead of evaporation or crystallization.

Industrial reuse loops where salt, color and residual surfactant must be removed from recovered water.


Competitive Position and Replacement Notes

LEFILTER elements are compatible replacement membranes evaluated against common industrial RO formats from brands such as DuPont FilmTec, Dow, Hydranautics, Toray, Suez and 3M. They are not original-equipment products of those manufacturers; brand references are for cross-reference and fit comparison only. Actual performance depends on feed water quality, pretreatment condition, recovery rate, temperature and operating pressure, and should be validated on-site before full skid operation.


Selection Guide

Flow target: 

choose format and number of elements to meet required reuse permeate flow and system recovery; do not oversize a single element beyond vessel and pump limits.

Feed quality: 

confirm upstream multimedia, carbon, softening and UF performance; if COD, color or turbidity at RO inlet is unstable, upgrade pretreatment before selecting a high-flux membrane.

Temperature and pH: 

verify feed stays within the membrane operating window; high temperature or out-of-range pH shortens membrane life.

Antiscalant and oxidation control: 

ensure antiscalant dosing and dechlorination are in place; residual chlorine or oxidants will degrade the polyamide membrane.

Reuse water standard: 

match membrane rejection to the target permeate conductivity and color limit for the receiving process.


Installation and Maintenance Notes

Flush and clean new vessels and piping before loading elements; remove construction debris, oil and residual chemicals.

Load elements gently with proper lubrication on seals; avoid dry twisting or seal damage during insertion.

Start pumps gradually, raise pressure and flow slowly to avoid membrane compaction and hydraulic shock.

Monitor permeate flow, conductivity, differential pressure and recovery trend; schedule CIP when flux drops or pressure rise indicates fouling.

Store spare elements wet in a preservative solution under the recommended temperature range; do not let membrane leaves dry out.


FAQ

Q1. Can this membrane treat raw dyeing wastewater directly?

A1: No. Raw dyeing effluent carries high color, COD, suspended solids, surfactant and oil load. It must go through pretreatment — pH adjustment, coagulation/filtration, softening, activated carbon and ultrafiltration — before reaching the RO stage.

Q2. What permeate quality can be expected for reuse?

A2: RO removes most dissolved salts, ionic species and residual color/organics rejected by the membrane; actual permeate conductivity and color depend on feed quality, recovery and pretreatment. Confirm against the receiving rinsing or washing water standard.

Q3. How often should CIP be performed?

A3: There is no fixed interval. Schedule cleaning when normalized permeate flow drops, conductivity rises or differential pressure climbs, following a monitored fouling trend rather than calendar time.

Q4. Is the membrane compatible with existing 8040 vessels?

A4: Standard 8040 and 4040 elements use conventional center tubes, end caps and seal arrangement. Verify vessel inner diameter, connector style and brine seal fit before installation.

Q5. What shortens membrane life in a dyeing reuse system?

A5: Poor pretreatment, residual chlorine or oxidants, excessive temperature, operation outside pH range, skipped antiscalant dosing, and delayed CIP all accelerate fouling, oxidation and irreversible performance loss.


Related Products 

BW30FR-400/34 Water Treatment RO Reverse Osmosis Membrane  

40-inch RO membrane water purifier membrane 

High Efficiency Reverse Osmosis Membrane for Water Treatment 

Commercial Reverse Osmosis Membrane for Pure Water System 

High Salt Rejection RO Membrane for Brackish Water Treatment

Please fill in your procurement needs and contact information

whatsapp