
Pleated Dust Collector Filter Cartridge for Sandblasting Workshop
Introduction:Sandblasting operations generate massive volumes of sharp, abrasive dust including steel grit, quartz sand and metal oxide particles. These fine dusts wear out filter media rapidly and easily cause equipment failure if filtration is inadequate. Our pleated dust collector filter cartridge is specially optimized for the harsh abrasive dust environment of sandblasting workshops. It adopts heavy-duty surface treatment and high-density filter media, effectively intercepting sharp dust particles and protecting downstream exhaust fans and pipelines. As a reliable alternative to imported filter cartridges from Donaldson and other brands, it helps sandblasting workshops reduce filter replacement frequency, meet local emission standards and maintain a clean working environment for operators.
We're here to help:
Easy ways to get the answers you need.
Product parameter:
Product Introduction
This pleated dust collector filter cartridge is custom-made for dry sandblasting, shot blasting and surface treatment workshops. As a core Dust Collector Filter, it can be matched with different types of cartridge dust collectors, and it also shares mature sealing and structural design ideas with the Air compressor filter, ensuring stable sealing performance and pressure resistance under continuous operation. The filter cartridge uses spun-bond polyester media with flame retardant, anti-static and wear-resistant coating, which greatly improves the resistance to cutting damage caused by sharp sandblasting dust. The whole structure is composed of a galvanized inner support cage, heavy-duty upper and lower end caps, high-elasticity sealing rubber ring and pleated filter material. It adopts vertical pleating technology to expand the effective filtration area, so it can hold more dust without rapid clogging. Compared with ordinary filter cartridges, this product is not easy to be scratched by abrasive particles, and the service life is significantly longer. It solves the common pain points of imported filter cartridges such as high purchase cost, long delivery cycle and insufficient wear resistance for abrasive dust, providing a cost-effective domestic replacement solution for global surface treatment factories, foundries and metal processing workshops.
Working Principle

Dust-laden air produced during sandblasting is sucked into the dust collector cabinet by the exhaust fan. The dusty airflow enters the filter cartridge from the outer side of the pleated filter media. Sharp sand grains, metal grit and fine oxide dust are trapped on the outer surface of the filter media, while the clean air passes through the filter layer, flows through the inner support cage and is discharged out of the equipment through the clean air outlet.
With the accumulation of dust on the surface, the pressure difference between the upstream and downstream of the filter cartridge gradually increases. When the differential pressure reaches the preset value, the pulse jet cleaning system will automatically start. Compressed air instantaneously sprays into the inner cavity of the filter cartridge, forming a strong airflow shock wave. The dust cake attached to the outer surface of the filter media is shaken off and falls into the dust hopper at the bottom of the dust collector. After the cleaning cycle, the filter cartridge restores its filtration capacity and continues to work. The pulse cleaning process is completed online without stopping the dust collection system, so the sandblasting production can run continuously. The special surface coating on the filter media also helps dust peel off smoothly during jet cleaning, reducing the risk of dust embedding into the fiber and causing permanent blockage.
Product Structure and Typical Specifications
| Item | Parameter Details |
|---|---|
| Filter Media | Spunbond polyester with anti-abrasion, anti-static coating |
| End Cap | Galvanized steel / Aluminum alloy |
| Inner Support Cage | Perforated galvanized steel |
| Sealing Ring | Nitrile rubber, high temperature resistant optional |
| Filtration Efficiency | ≥99.9% for 5μm particles |
| Working Temperature | -20℃ ~ 80℃ |
| Air to Cloth Ratio | 0.8 ~ 1.2 m/min for sandblasting dust |
| Common Size | 325×660mm, 325×1300mm, 350×900mm, customizable |
| Installation Method | Top mount / Bottom mount |
| Cleaning Mode | Pulse jet compressed air cleaning |
Core Advantages
Excellent abrasion resistance for sharp dust:
The special surface treatment avoids the filter media being scratched and punctured by steel grit and quartz sand, solving the biggest failure problem of ordinary filter cartridges in sandblasting workshops.
High dust holding capacity:
Deep pleat design expands the filtration area, slows down the differential pressure rise speed and extends the service interval.
Anti-static property:
Effectively prevents static electricity accumulation caused by high-speed friction between dust and fiber, reducing explosion risk in workshops with combustible metal dust.
Good pulse cleaning performance:
Dust is not easy to stick to the media surface, the dust cake falls off completely during jet blowing, and the filter cartridge will not be blocked quickly.
Wide compatibility:
It can directly replace mainstream imported filter cartridges, fits most brands of cartridge dust collectors without modifying the equipment structure.
Strict quality control:
Each cartridge is tested for air permeability, bubble point and sealing performance before delivery, stable and consistent batch quality.
Application Scenarios

Dry sandblasting workshop dust collection system
Shot blasting machine and wheel blasting equipment dust removal
Foundry sand cleaning and metal grinding dust treatment
Steel structure anti-corrosion surface treatment production line
Hardware factory polishing and abrasive processing dust removal
Mining equipment maintenance blasting room exhaust filtration
Surface treatment workshop waste gas pre-filtration
Selection Guide
Confirm the installation way:
top installation or bottom installation, and measure the original cartridge diameter, length and thread size.
Judge dust characteristics:
quartz sand, steel shot, aluminum oxide grit or other abrasive dust, to confirm whether anti-static and enhanced wear-resistant coating is required.
Calculate the total air volume of the dust collector, and match the proper air-to-cloth ratio. Sandblasting abrasive dust needs a lower air-to-cloth ratio than ordinary dust.
Confirm working temperature:
ordinary polyester media is suitable for normal temperature; high temperature media is optional for hot blasting process.
Check the compressed air supply of the pulse system:
stable 0.4–0.6 MPa compressed air is required to guarantee the cleaning effect.
For metal aluminum, magnesium and other combustible dust, anti-static filter cartridge must be selected and equipped with explosion-proof accessories.
Installation & Maintenance Notes
Before installation, check whether the filter cartridge surface is damaged, and confirm that the sealing ring is intact and free of cracks. Do not remove the plastic packaging until installation to avoid accidental scratches. When installing, align the filter cartridge vertically with the mounting hole, and tighten the fixing parts evenly to prevent air leakage from the sealing position. Air leakage will lead to dust bypass and rapid wear of the filter media.
Regularly observe the differential pressure gauge of the dust collector. If the differential pressure keeps rising rapidly after pulse cleaning, it means the filter cartridge has been embedded with dust and cannot be cleaned, and replacement is needed in time. During daily maintenance, avoid hitting the filter cartridge with hard tools. When cleaning the dust hopper, shut down the fan and cut off the power supply to ensure safety. Do not use high-pressure water to wash this dry-type filter cartridge, which will cause permanent blockage of the fiber media.
FAQs
Q1: Why do ordinary filter cartridges break easily in sandblasting workshops?
A1: Sandblasting dust is sharp and hard. Ordinary polyester filter media without anti-abrasion coating will be cut and pierced by sand particles under high-speed airflow. Our cartridges adopt heavy-duty surface coating to resist the cutting of abrasive dust, greatly prolonging service life.
Q2: Is this filter cartridge anti-static?
A2: Yes, the standard version is anti-static. It is suitable for aluminum, magnesium and other combustible metal dust blasting workshops to reduce static hazards. We can provide ordinary non-static versions for inert quartz sand blasting as required.
Q3: Can it work with my existing Donaldson cartridge dust collector?
A3: Yes, we support compatible replacement. You only need to provide the size and part number of the original filter cartridge, we will match the same size and installation structure for direct replacement without equipment modification.
Q4: What is the typical service life in a sandblasting workshop?
A4: It depends on dust concentration and working hours. Normally, it can work for 3–6 months under continuous sandblasting conditions. If the dust concentration is extremely high, the service life will be shortened accordingly. Differential pressure is the most reliable indicator for replacement.
Q5: Can I customize special sizes?
A5: Absolutely. We support non-standard size customization, different end cap structures, special coating and high-temperature media options according to your dust collector drawing and working conditions.
Related Products
Filter Cartridge Dust Collector lefilter P191526-016-436
P19-1006 Dust Collection Filter Cartridges
P19-1037 lefilter dust collector cartridge filter
Please fill in your procurement needs and contact information








